Tap & Shower Repair in Wimbledon

Pricing depends on the scope of work, parts required and time on site. Our engineer will quote a fixed price before any work starts at your Wimbledon property — no surprises on the invoice.

Yes. Every engineer is fully insured (£5m public liability), DBS-checked and — for any boiler or gas work — Gas Safe registered. We send the right qualified person for tap & shower repair in Wimbledon.

For genuine emergencies we aim to be on site in Wimbledon within the hour, 24/7. For pre-booked work, same-day or next-day slots are usually available across Wimbledon and the surrounding areas.

Yes — all plumbing repairs come with a workmanship guarantee, and replacement parts carry the manufacturer's warranty. For boiler repairs the parts & labour guarantee is 12 months.

Yes. We work in homes, flats, HMOs, restaurants, offices, shops and managed buildings across Wimbledon and the surrounding areas — including landlords, letting agents and facilities companies.

A continuously dripping shower tap usually needs its washer, cartridge or seals repaired or replaced. First distinguish a persistent leak from water briefly draining out of the shower head after use. If the drip continues, isolate the supplies and identify the valve model before buying parts. Clean accessible debris and fit the correct replacement, following the manufacturer's instructions. For concealed valves, seized fittings or an uncertain diagnosis, a plumber can investigate without unnecessary dismantling or damage to surrounding finishes.

First check whether your shower tap uses a rubber washer: quarter-turn and thermostatic controls usually use cartridges instead. For a traditional washer tap, isolate the water, open the tap to confirm it is off, then remove the handle and unscrew the valve assembly. Replace the washer at its base with one of the same size and type. Inspect the seat, reassemble gently and test. Avoid dismantling a concealed shower valve without identifying the model and isolation points.

Replacing separate shower taps with a mixer requires checking the hot and cold supplies, pipe spacing and compatibility with your water pressure and heating system. A thermostatic mixer helps control temperature, but must suit the installation. Isolate both supplies before removing fittings; pipework alterations or access behind tiles may be necessary. An engineer can fit the appropriate connections, flush the supplies, test for leaks and commission the temperature control. This is not always a direct swap.

To fix a dripping kitchen tap, first isolate its hot and cold water supplies, then open the tap to check the flow has stopped. Cover the plughole before removing the handle and valve. Traditional taps often need a new washer; ceramic-disc models generally require a matching cartridge. Inspect the valve seat for debris or damage and avoid overtightening during reassembly. Restore the water slowly and check for leaks. Stop if fittings are seized or isolation is ineffective.

Emergency Plumber London offers fixed-price repairs from £120+VAT for dripping taps in Wimbledon. The repair needed depends on whether the fault is a washer, cartridge, seal or damaged tap body. Your price is confirmed on the phone before an engineer is sent, with the same price day, night, weekends and bank holidays. Call 07307 202652 to describe the leak and arrange a repair. Work comes with a 12-month workmanship guarantee.

Dripping taps commonly result from worn rubber washers, damaged ceramic cartridges, limescale or debris preventing a watertight seal. A pitted valve seat can make a traditional tap drip even after its washer is replaced. Water around the handle or base more often points to worn seals or O-rings rather than the spout valve. Identifying exactly where the water escapes helps determine the repair; tightening the handle harder rarely solves the underlying problem.

You do not always need a plumber for a dripping tap: replacing a washer on a traditional tap can be a straightforward DIY job if you can safely isolate the water. Ceramic-disc taps usually need a matching cartridge instead. Call a plumber if the isolation valve will not close, fittings are seized, the tap leaks underneath, or you are unsure which parts fit. Avoid forcing the handle tighter, as this can damage the mechanism.

A shower tap that keeps dripping when switched off usually has a worn washer, damaged cartridge or deteriorated valve seal. Limescale and grit can also stop the valve closing properly. Brief dripping from the shower head after use may simply be trapped water draining out. If it continues, isolate the water before dismantling anything. The repair normally involves cleaning the valve seat or replacing the faulty washer, seals or cartridge with compatible parts.